Swiftin Agencies LLP

It is not necessary to manufacture a hole for the installing and you just need to use bolt to fix the swing clamp on the fixture plate. It is helpful for you to clamp thick workpiece because the main structure of the cylinder body is on the fixture plate.Feature of the doubling acting type: Oil circuits control clamping and unclamping, you can control the clamping and unclamping by changing the direction value.Feature of the single acting type :The design of the interior system is simple. It is not necessary to design for unclamping. It can return back to the original position by spring and the system design is simple because of few accessories.The material of the cylinder body is carbon steel and treated by nicarbing. The hardness of the outside and inside surface of the cylinder is high and the cylinder is anti abrasive.
Max.operating pressure: 250 kgf/cm²Min.operating pressure: 70 kgf/cm²Single acting and Double acting

NOTE:The action and the speed of clamping / unclamping needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for the rotation diagram, installation instructions and removal methods of the clamping arm.
Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade

Product InformationA hydraulic swing clamp is a clamping device that converts hydraulic pressure into a clamping force to secure the pieces. When the NFS hydraulic swing clamp is in action, it clamps down vertically after rotating to the left or right.The cylinder's body is manufactured with highgrade carbon steel and processed with hardened surface treatment.The standard angle is 90 degrees, options to customize the angle at 30 degrees, 45 degrees, or 60 degrees are available. Installation of a flow control valve at the oil inlet is highly recommended to control the swinging speed and avoid inertial impact. When the hydraulic cylinder is clamping and pressing downward, the workpiece should be clamped within the lock stroke range.During the workpiece's loading & unloading period, please be sure to clean the oil seal from the piston rod with an air gun to avoid embedding any particles and chips.

Max. operating pressure: 210 kgf/cm²Min. operating pressure: 70 kgf/cm²Single acting and Double acting.

NOTE:The action and the speed of clamping / unclamping needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for the rotation diagram, installation instructions and removal methods of the clamping arm.Customization is available upon request, please contact us for more info.
Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade.

 

ASC-25 To ASC-63

This machine with MC clamp is exclusively to mass-produce spare parts. It is a big helper to raise production efficiency. The clamping arm of this clamp will swing around the angle when the piston traveling down, and then keep straight on until the clamping arm clamps the work-piece tightly.You had better install a flow control valve to adjust the acting speed, and don't clamp the workpiece when the clamp is running, Otherwise will be easy to damage the body and the spare parts.The material of the cylinder body is made of aluminum metal alloy, the surface is processed with the hard membrane and the inside of it is smooth. It is long-lived to use.
Max. operating pressure: 7 kgf/cm²Min.operating pressure: 4 kgf/cm²Double acting

NOTE:The speed of clamping and unclamping action needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for installation instructions or removal methods of the clamping arm.Customization is available upon request, please contact us for more info.
Usable fluid:Filtered dry compressed air.

PBS-25 to PBS-50 Available.

Simple and compact structure, lightweight, high clamping capacity, and long product lifespan.This series has the option of choosing a long or a short stroke, which can be installed at the top or the bottom.

It is widely used in industrial automation, such as clamping of sheet metal, clamping of workpieces on conveyor belts, and packaging assembly line operations.
Max. operating pressure: 7 kgf/cm²Min. operating pressure: 4 kgf/cm²Double acting

NOTE:The speed of clamping and unclamping action needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for installation instructions or removal methods of the clamping arm.Customization is available upon request, please contact us for more info.
Usable fluid:Filtered dry compressed air.

PSB-25 to PSB-63 Available.

Simple and compact structure, lightweight, high clamping capacity, and long product lifespan. This product can be equipped with sensor switches with the option to install on the top, bottom or on the side.
Max.operating pressure: 7 kgf/cm²Min.operating pressure: 4 kgf/cm²Double acting.

NOTE:The speed of clamping and unclamping action needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for installation instructions or removal methods of the clamping arm.Customization is available upon request, please contact us for more info.
Usable fluid:Filtered dry compressed air.

25 bore dia - 80 bore dia Available.

Product InformationThe CHS/HSC series is made with industrial grade carbon steel and processed with hardened surface treatment to increase durability and extend product lifespan. It is designed to increase production efficiency for machinery and MC fixtures used for mass production. During the actuation state, the piston rod will drive the clamping arm downward and rotate to the desired position and angle. When the swing clamp is in action, the piston rod will drive the clamping arm to press down and rotate to the desired position and angle, thereby clamping the workpiece. For operational instructions, do not clamp the workpiece during the rotation. Also, installation of a flow control valve is highly recommended to help avoid excessive speed.
Max.operating pressure: 70 kgf/cm²Min.operating pressure: 15 kgf/cm²Double acting

NOTE:The action and the speed of clamping / unclamping needs to be slowed down appropriately.The length and weight of the customized clamping arm shall not exceed 1.5 times of the standard clamping arm.Please refer to Q&A for the rotation diagram, installation instructions and removal methods of the clamping arm.
Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade

M26 To M45 Available.

High Supporting Force: The gap between the plunger and the collet is expanded to improve its overall performance, resulting in a higher supporting force.Cutting Fluid Cleaning Countermeasures: To prevent improper operation caused by high-pressure coolant and chip dust from entering the internal structure, air cleaning can be performed in the exhaust hole when replacing the workpiece. Air cleaning requires a specific air pressure circuit (recommended cleaning air pressure at 0.3~0.5MPa).Universal piping base: The CSP series is compatible and interchangeable with Japanese branded cylinders that are currently on the market.
Hydraulic Pressure Rising Type:The initial state of the piston rod is down. When the oil pressure is supplied, the piston rod rises and stops once contact is made with the workpiece at any position. During this period, the hydraulic pressure on the collet can grip the plunger with stronger power to generate the supporting force.
Spring Rising Type:The initial state of the piston rod is up, and the workpiece is placed on the piston rod and dropped to a certain distance due to the weight of the workpiece. During this period, the hydraulic pressure on the collet can grip the plunger with stronger power to generate the supporting force.

Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade.

036 to 105 Available.

The accessories of the CHA series are optimally designed to create a more compact-sized product with enhanced strength. With its special dust-proof design, this product has improved its sealing performance and protects against any particles or debris while in use. The product's structure design has a high torsion resistance that achieves maximum durability.
Max. operating pressure: 70 kgf/cm²Min. operating pressure: 15 kgf/cm²Double acting

NOTE:The action and the speed of clamping/unclamping needs to be slowed down appropriately.Please refer to Q&A for installation instructions or removal methods of the clamping arm.Customization is available upon request, please contact us for more info.
Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade.

The CHTB series' compact construction helps conserve work space and can be utilized in restricted areas. With the standardized structure, the cylinder can be installed directly and does not require any accessories to operate. The CHTB hydraulic cylinders are manufactured with industrial grade carbon steel. The smooth interior is processed specifically to enhance product performance and increase product lifespan.
Cylinder Inside Dia options - Ø20, Ø25, Ø32, Ø40, Ø50, Ø63, Ø80Max. operating pressure: 140 kgf/cm²Min. operating pressure: 5 kgf/cm²Double acting

NOTE:Customization is available upon request, please contact us for more info.CHTB-LAM and CHTB-LWM series, stroke 10mm without keyway and parallel key.
Usable fluid:ISO-VG-32 hydraulic oil equivalent to ISO viscosity grade.